Software & Tools

    EPD Compliant Software 2026: What Regulatory Changes Demand from Your LCA Tools

    The revised Construction Products Regulation, Digital Product Passports, the EPBD, EU green-claims rules and CBAM are reshaping what EPD compliant software must do in 2026 — from the full EN 15804+A2 indicator set to machine-readable EPD data.

    12 min read

    The Regulatory Context Driving EPD Demand in 2026

    The phrase "EPD compliant software" means something different in 2026 than it did in 2022. Several EU and national rules are turning product-level environmental data from a voluntary marketing document into regulated information, and software built for voluntary EPD programmes is meeting requirements it was not designed for.

    Five regulatory drivers matter most. Understanding each one clarifies what your software stack needs to handle.

    Construction Products Regulation (CPR)

    The revised CPR, Regulation (EU) 2024/3110, has applied since 8 January 2026 and is the most direct legal driver for construction EPD data. Its new Declaration of Performance and Conformity (DoPC) brings environmental sustainability into CE marking. Global warming potential (GWP) comes first, product family by product family, as the harmonised technical specification for each family is revised to require it. The other environmental indicators listed in Annex II are phased in over the following years; industry guidance points to 2030 and 2032.

    These indicators are calculated on an EN 15804 basis. For construction products, EPD-grade LCA is therefore becoming part of the legal product declaration, not only a voluntary document. The CPR also creates a Digital Product Passport for construction products, covered below.

    Energy Performance of Buildings Directive (EPBD) and national building rules

    The recast EPBD, Directive (EU) 2024/1275, requires the life-cycle GWP of new buildings to be calculated and disclosed in the energy performance certificate: from 1 January 2028 for new buildings over 1,000 m², and from 1 January 2030 for all new buildings. Member States must also set out how they will introduce life-cycle GWP limit values for new buildings.

    Several countries already regulate embodied carbon at building level. Sweden has required climate declarations for most new buildings since 2022. Denmark has set CO2 limit values for new buildings in its building regulations (BR18) since 2023. Norway's TEK17 has required a greenhouse gas account for new apartment and commercial buildings since July 2022. France's RE2020 sets carbon thresholds for new buildings, calculated with FDES and PEP declarations from the INIES database or with default values.

    These building calculations use product-specific EPDs where they exist and generic or default data where they do not, and default data is often deliberately conservative. Public buyers that score embodied carbon in tenders also typically accept verified EPDs as evidence. A product without a current EPD is at a disadvantage in all of these settings.

    Ecodesign for Sustainable Products Regulation (ESPR)

    The ESPR, Regulation (EU) 2024/1781, entered into force on 18 July 2024. It is a framework regulation: requirements for a product group, including whether it needs a Digital Product Passport and what that passport must contain, apply only once the Commission adopts a delegated act for that group. The ESPR Working Plan 2025–2030 prioritises iron and steel, aluminium, textiles, furniture, tyres and mattresses. As of mid-2026 no product-specific delegated act had been adopted; iron and steel is first in line.

    Where a delegated act requires an environmental or carbon footprint, the ESPR points to the Product Environmental Footprint (PEF) method or other scientific methods — not to EN 15804 or ISO 14025 EPDs as such. How far existing EPD data can be reused will depend on the rules in each delegated act. For construction products, environmental and passport requirements are being set under the CPR instead.

    Green claims rules

    The Empowering Consumers for the Green Transition Directive, Directive (EU) 2024/825, has applied since 27 September 2026. It bans generic environmental claims such as "eco-friendly" or "green" unless the trader can demonstrate recognised excellent environmental performance, and it bans claims that a product has a neutral, reduced or positive climate impact based on carbon offsetting. It applies to claims made to consumers.

    The separate Green Claims Directive proposal, which would have set detailed substantiation and pre-verification rules for explicit environmental claims, stalled in June 2025 when the Commission announced its intention to withdraw it and the planned final trilogue was cancelled. It has not been adopted. No EU law makes an EPD the only accepted basis for an environmental claim, but a verified, ISO 14040/14044-based LCA or EPD remains among the strongest evidence a company can hold for a specific claim.

    Carbon Border Adjustment Mechanism (CBAM)

    CBAM's definitive period began on 1 January 2026 for imports of cement, iron and steel, aluminium, fertilisers, electricity and hydrogen. The 2025 simplification, Regulation (EU) 2025/2083, exempts importers below a 50-tonne annual threshold for most of these goods. The first annual declaration, covering 2026 imports, is due by 30 September 2027, and certificate sales start in February 2027.

    CBAM uses its own embedded-emissions method based on EU ETS monitoring rules, not EN 15804 or ISO 14067. The production data it needs (energy use, process emissions, precursor materials) overlaps heavily with the A1–A3 data behind an EPD for steel, aluminium or cement, so manufacturers in these sectors benefit from software that keeps one consistent set of primary data.

    What "EPD Compliant" Means for Software in 2026

    Compliance is now a multi-layered requirement. Software must satisfy:

    1. Methodological Standards

    • EN 15804:2012+A2:2019: The core European standard for construction product EPDs. Under A2, modules A1–A3, C1–C4 and D must be declared for almost all products; a cradle-to-gate declaration is allowed only when three specific conditions are all met. A2 defines core environmental impact indicators (with GWP split into fossil, biogenic, and land use and land use change), additional impact indicators, and resource use, waste and output flow indicators. Characterisation factors come from the European Commission's Environmental Footprint (EF) reference package.
    • ISO 14025:2006: The framework for Type III environmental declarations, under which programme operators run their EPD programmes.
    • ISO 21930:2017: The international core rules for EPDs of construction products and services — the ISO counterpart to EN 15804.
    • Product Category Rules (PCRs): For construction products in the International EPD System, PCR 2019:14 Construction products applies (version 2.0, which replaced version 1.3.4 in 2025), supplemented by complementary PCRs (c-PCRs) for specific product groups. Outside construction, the product-specific PCR of your programme operator sets the rules.

    2. Programme Operator Acceptance

    A tool must produce outputs accepted by your target programme operator. This is not automatic even for methodologically sound tools. Programme operators such as IBU (Germany), the International EPD System (Sweden) and EPD-Norge (Norway) each set their own general programme instructions, templates and submission processes, and some approve EPD generator tools or certified EPD processes under their own procedures. Programme operators also decide which characterisation factors they accept: the International EPD System and EPDItaly, for example, now require EF 3.1 for new EPDs.

    Verify acceptance directly with your programme operator before committing to a tool, especially for new-to-market platforms.

    3. Machine-Readable Output

    EPD data increasingly needs to be machine-readable, not only human-readable. The formats and tools that matter:

    • ILCD+EPD: The European Commission's ILCD data format, extended for EN 15804 for Germany's ÖKOBAUDAT database and now maintained by the InData network. ECO Platform's Digital Data Requirements (2024) set out how machine-readable ECO EPDs are published in ILCD+EPD, and the ECO Portal gives access to digital EPD data from ECO Platform programme operators.
    • soda4LCA: Open-source database software for publishing ILCD and ILCD+EPD datasets through a web service interface. ÖKOBAUDAT is built on it. It is software, not a data standard.
    • ISO 22057:2022: Data templates for using EPD data for construction products in Building Information Modelling (BIM).

    Software that only exports PDF EPDs cannot take part in machine-readable data exchange. This was a marginal issue in 2022; it is a real limitation in 2026 for organisations whose programme operator publishes digital EPDs or whose customers import EPD data into building LCA tools.

    Digital Product Passports: What EPD Software Must Connect To

    A Digital Product Passport (DPP) is not a single EU database. Each passport is a structured product record with a unique identifier, reached through a data carrier such as a QR code. The data stays with the economic operator or a service provider acting for it. The European Commission's DPP registry, launched in July 2026, stores passport identifiers so that customs and market surveillance authorities can find them.

    How passports work technically is set by European standards. CEN and CENELEC's Joint Technical Committee 24 (CEN-CLC/JTC 24), working under the Commission's standardisation request M/604, published the first DPP standards in 2026: EN 18219 (unique identifiers), EN 18220 (data carriers), EN 18216 (data exchange protocols), EN 18221 (data storage, archiving and persistence), EN 18222 (APIs for lifecycle management and searchability) and EN 18223 (system interoperability). Further standards on access rights, security and data authentication are in progress. These standards are product-agnostic: they define how a passport is identified, stored and exchanged, not what it contains.

    What a passport must contain is set by product legislation, and this is where EPDs come in.

    Construction products: The CPR sets up its own construction DPP system, to be established by a Commission delegated act. Manufacturers must make a passport available 18 months after that act enters into force, connected to a data carrier. The passport is to carry the Declaration of Performance and Conformity, including its EN 15804-based environmental indicators, alongside instructions for use and safety information. This is the most direct route by which EPD-grade LCA results will reach a passport. The delegated act had not been adopted at the time of writing, so no construction DPP data schema exists yet.

    ESPR product groups: Passports for steel, aluminium, textiles and other ESPR product groups will follow each group's delegated act. Any environmental or carbon footprint those acts require will use the method each act specifies, with PEF as the main EU reference method, so EPD data may need to be recalculated or mapped rather than copied across.

    Batteries: The Batteries Regulation, Regulation (EU) 2023/1542, requires a battery passport from 18 February 2027 for electric vehicle batteries, light means of transport batteries and industrial batteries above 2 kWh. It is the first DPP with a fixed legal start date, but it is not yet in operation. Its carbon footprint declaration follows a battery-specific method set by delegated act, not EN 15804, and that act was still pending in mid-2026.

    For EPD authors, the near-term task is not to connect to a passport system, because for most products none exists yet. It is to hold LCA results as structured data: indicators per module, declared or functional unit, system boundary, reference service life, PCR and version, validity dates, verification status and a unique product reference. ILCD+EPD is the established format for digital construction EPDs and a sensible starting point, and ISO 22057 already maps EPD data into BIM. Expect the construction passport data model to come from the CPR delegated act and the related harmonised technical specifications, and treat any vendor claim of "DPP-ready" output as unproven until that act exists.

    The Shift from Static PDFs to Machine-Readable EPD Data

    The EPD industry is moving from declaration-as-document to declaration-as-data. This shift has several practical dimensions:

    Downstream use in building LCA tools: Building LCA software, including the calculation tools used for national building regulations, needs EPD data in structured form. Static PDFs require manual data entry; ILCD+EPD data can be imported directly.

    EPD databases: The ECO Portal, ÖKOBAUDAT (Germany) and INIES (France) distribute EPD data in machine-readable form, and ECO Platform's Digital Data Requirements set common rules for digital ECO EPDs.

    Supply chain data requests: Customers building Scope 3 inventories ask suppliers for product-level data. A supplier whose EPDs exist only as PDFs creates manual work for its customers.

    Version management: Products change. When a product is reformulated or a process improves, updating an EPD and propagating that update to all downstream users requires machine-readable version tracking — not a new PDF sent by email.

    For 2026, a software evaluation should explicitly assess: "Can this tool deliver EPD results in a structured, machine-readable format that a programme operator or downstream system can import?"

    What Organizations Should Look for in 2026-Ready EPD Software

    Use this checklist when evaluating platforms against 2026 requirements:

    1. EN 15804+A2 full indicator set: Confirm that all core and additional impact indicators, plus the resource use, waste and output flow indicators, are calculated and reported for every declared module.
    2. EF 3.1 characterisation factors: Programme operators such as the International EPD System now require EF 3.1 for new EPDs. Tools using EF 3.0, older EF versions or CML factors need checking against your programme operator's rules.
    3. ILCD+EPD export: Needed if your programme operator publishes digital EPDs, for example as ECO EPDs on the ECO Portal. Confirm the export conforms to the ILCD+EPD version your programme operator accepts.
    4. PCR version tracking: The tool should alert you when a PCR you work under is updated or expires, since a new or renewed EPD must be verified against a valid PCR version.
    5. DPP readiness: Ask the vendor how it tracks the CPR passport delegated act and the CEN-CLC/JTC 24 standards, and in which structured format it can hand over EPD data today. A vague answer is a risk flag; so is a claim of full DPP compliance before the data requirements exist.
    6. Claim defensibility: Can the tool produce a verification-ready LCA report that a third-party verifier can sign off on? This means documented data quality, traceable background data and a clear audit trail — the same evidence you need to substantiate environmental claims.
    7. Multi-region compliance: If you operate across jurisdictions, confirm the tool supports the PCRs and programme operators relevant to each market.
    8. Data governance and access controls: Personal data in your LCA workflow falls under GDPR, and supplier process data is often commercially confidential. Cloud-based tools should offer data residency options and clear data processing agreements.

    Emerging Requirements: Beyond 2026

    Looking further forward, sustainability managers should be aware of requirements that are not yet mandatory but are moving toward it:

    • Building-level limit values: Under the EPBD, Member States must set out how they will introduce life-cycle GWP limit values for new buildings. Limit values raise the value of product-specific EPDs over conservative default data.
    • Scope 3 integration: EPD data can feed supplier-specific Scope 3 inventories. Since the Omnibus I amendments took effect in March 2026, the CSRD applies to EU companies with more than 1,000 employees and more than €450 million net turnover, but those companies still pass data requests down their supply chains.
    • Comparability across EPDs: EPDs are often not comparable because of differing PCRs, system boundaries, background data and allocation choices. EN 15804+A2, c-PCRs and the CPR's common environmental indicators all push toward more consistent declarations. Software that enforces consistent methodological choices will produce EPDs that hold up under this scrutiny.
    • Faster verification: The back-and-forth between EPD authors and verifiers remains a bottleneck. Tools that give verifiers structured access to the model, data sources and data quality documentation shorten that cycle.

    Choosing Software for 2026 and Beyond

    The organizations that will navigate the 2026 regulatory environment with least friction are those that have already:

    • Kept their LCA results as structured data, with a route to ILCD+EPD output through their tool or programme operator
    • Built internal processes around verified, machine-readable EPD data
    • Chosen programme operators that publish digital EPDs and follow the CPR passport work
    • Created internal capacity to update and re-verify EPDs when PCRs or underlying processes change

    ClimatePoint covers the LCA side of this: EN 15804+A2 modelling (modules A1 to D), PCR matching against a PCR index, and an LCA project report and draft EPD generated in the platform for your third-party verifier, with our analysts building the study, or reviewing it on request. It does not export ILCD+EPD data and does not register or publish EPDs; your programme operator does that. If you are assessing your software readiness for 2026 regulatory requirements, book a call with our team at climatepoint.com to discuss your product categories and target program operators.

    Sources

    Last reviewed: October 2026. Regulatory timelines in this area move quickly; check the official texts before relying on a date.

    • Regulation (EU) 2024/3110 (Construction Products Regulation)
    • Directive (EU) 2024/1275 (Energy Performance of Buildings Directive, recast)
    • Regulation (EU) 2024/1781 (Ecodesign for Sustainable Products Regulation) and the ESPR Working Plan 2025–2030, COM(2025) 187
    • Directive (EU) 2024/825 (Empowering Consumers for the Green Transition)
    • Regulation (EU) 2023/956 (CBAM), as amended by Regulation (EU) 2025/2083
    • Regulation (EU) 2023/1542 (Batteries Regulation)
    • CEN-CLC/JTC 24 Digital Product Passport standards EN 18216 and EN 18219 to EN 18223 (2026)
    • EN 15804:2012+A2:2019, ISO 14025:2006, ISO 21930:2017 and ISO 22057:2022
    • ECO Platform, Digital Data Requirements V1.0 (2024)
    • International EPD System, PCR 2019:14 Construction products, version 2.0
    • Nordic Council of Ministers, Harmonised Carbon Limit Values for Buildings in Nordic Countries (2024)